1.Dress
Fold 0.8cm(1/3”) twice concealing the cut edge of frill (straight line) and press.
Sew the hem as shown.
Sew a parallel row of long(gathering) stitches around the frill.
(Stitch length long, tension low/loose)
(1) Round shape
Gathering the frill.
Stitch the frills to the bodice with right sides together as shown.
Pin and sew the front and front York pieces together with right sides of fabric together.
Serge or zigzag stitch the edges as shown.
(2) Square shape
Fold 1cm(3/8") of side edges and bottom edge of front panel.
Stitch the frills to the bodice with right sides together as shown.
Pin the front and front panel pieces together.
Edgestitch them together.
(3) Pentagon shape
Pin the front and front panel pieces together.
Edgestitch them together.
(4) Round shape
Pin the front and front panel pieces together.
Edge stitch them together.
Apply interfacing to the wrong side of back button placket 4cm(1.6”) wide.
Fold the 1cm(3/8”) from the raw edge to the wrong side
and fold and press 3cm(1.2”) to the wrong side again. Repeat with the other piece.
Pin and sew the shoulders of front and back together with right sides of fabric together.
Serge or zigzag stitch the shoulders together as shown.
Press seams towards the back.
Press 3/8″(1cm) bias bindings in lengthwise.
Then fold the 1cm(3/8inch) from the raw edge to the wrong side.
Then the fold 3cm(1.2inch) to the to the right side as shown. Then pin them for fixing.
Now pin your bias tape to the bodice neckline with right side together.
Trim the points on any sharp angles and cut half of the seam allowance along the curve.
Turn the button placket part inside out.
And fold the binding to the inside of the garment,
rolling the seam line in slightly to hide it on the inside of the garment.
Fold the raw edge of the binding under along the line you pressed earlier,
and pin this fold to the inside of the neck line.
Continue to press the binding to the other side.
Topstitch the binding to the neck line close to the inside fold.
Then edge stitch button placket as shown. Repeat with the other piece.
Make the button holes as shown.
On the wrong side of sleeves, fold 1cm(3/8") and 1.5cm(5/8")
concealing the cut edge and press. Sew the hem of sleeve as shown.
Sew a parallel row of long(gathering) stitches around the top sleeve.
(Stitch length long, tension low/loose)
Gathering the top edge of sleeve.
Stitch sleeves and armhole together as shown. Serge them together.
Pin and stitch the front and back together as shown, right sides of fabric together.
Serge or overlock them together.
Using your CB (center back line) as a guide, lay your left piece overlapping the right piece and pin in place. Sew the baste stitch.
On the wrong side of sleeve, fold twice concealing the cut edge. Pin all the way around sleeve hem line and sew. Stop your line of stitching about 2.5cm (1”) before you reach the point where you began this leaves you an entrance hole to access your elastic band tunnel.
Pull the elastic band trough the tunnel with the help of a safety pin.
Lap the ends of the elastic by half inch and stitch them together.
Sewing the opening shut.
Sew a parallel row of long (gathering) stitches around the waist line of skirt.
(Stitch length long, tension low/loose)
To gather the skirt fabric simply hold the fabric still in one hand and pull one of the loose threads with the other. Do this on both sides until your skirt is the same width as the each waist.
Repeat with the other piece.
Face the right sides of skirt together. Pin on and stitch along the side lines.
Serge or zigzag red line at the edge as shown. Press seams towards back.
On the wrong side of hem, fold 1cm(3/8") and 1.5cm(5/8")
concealing the cut edge and press. Sew the hem of skirt as shown.
Match the skirt to bodice waist line with right sides together as picture shown.
Align the skirt and bodice right sides together.
Pin all the way around waist line and sew as shown.
Serge or do zigzag the raw edge.
Sew a parallel row of long(gathering) stitches around the romper.
To gather the front romper pants simply hold the fabric still in one hand and pull one of the loose threads with the other.
Apply interfacing to the wrong side of snap button placket (2.5cm/1” wide).
Face the right sides of front romper pants and back romper pants together. Pin on and stitch along the side lines. Serge or zigzag red line at the edge as shown. Press seams towards back.
Serge or do zigzag the raw edge of leg line as shown.
On the wrong side of leg line, fold 1.5cm/5/8inch concealing the cut edge and press as shown.
And edge stitch along the leg line as shown.
Match the romper to bodice waist line with right sides together as picture shown.
Align the romper and bodice right sides together.
Pin all the way around waist line and sew as shown. Serge or do zigzag the raw edge.
On the wrong side of leg line, fold 1.25cm(1/2inch) concealing the cut edge and press as shown.
And edge stitch along the leg line as shown.
Pull the elastic band trough the tunnel with the help of a safety pin. Do a small stitch the elasticband to the begining and end of leg line at both sides to fix as picture shown.
And Serge or do zigzag the raw edge of snap button placket.
On the wrong side of placket, fold 2.5cm(5/8 inch)once concealing the cut edge and press.
Sew the croth line as shown. Repeat with the other side.
Add snaps to the front and back placket.
댓글
댓글 쓰기