1. Pinafore dress with frill strap
Serge the edge line of frill.
Fold 0.5cm(3/16”) concealing the cut edge and press. Sew the hem as shown.
Sew a parallel row of long(gathering) stitches around the frill. (Stitch length long, tension low/loose)
Gathering the frill.
Pin the frill to the strap with right sides together as shown.
The face of both strap pieces should be touching. Sandwich a frill between two straps.
Then sew the straps and frills together with right sides together as picture shown.
Leave unstitched 1cm(3/8”) from back as shown.
Match the front and front facing together. Face the right sides. Sew the top sewing line as shown. Turn right side out. and Press the top seam line.
Sew the baste stitch of the sides.
Face the right side of strap and front. Match the front bottom edge and strap front edge as shown. Then sew the side line of front as shown.
Then fold in half with the right side and sew down the short side of back and 7cm(2 3/4”)
of strap as shown.
Turn it right side out.
Fold and press strap 1cm(3/8”) in horizontally to the wrong side.
Edgestich along length of strap as shown. Repeat with the the other strap .
Sandwich the top front between front bands. Sew along the bottom.
Press seams open.
Match the front band and back band. Face the right sides. Stitch as shown, keeping opening unstitched. Press seams open.
Fold and press seam 1cm(3/8”) of waistband-inside in horizontally to the wrong side.
Sew a parallel row of long(gathering) stitches around the front skirt.
To gather the front skirt simply hold the fabric still in one hand and pull one of the loose threads
with the other.
Do this on both sides until your front skirt is the same width as the front waist band.
Face the right sides of skirt together.Pin on and stitch along the side lines.
Serge or zigzag at the edge as shown.
Press seams towards front.
Sew the waistband-outside to the skirt as shown. Face the right sides. And fold and press seam 1cm(3/8”) of waistband-inside in horizontally to the wrong side.
Fold the waistband down lengthwise along the pressed fold.
Top stitch along the bottom of the waistband (about 1/8 inch from the seam between the waistband and the skirt), making sure you're catching the inside of the waistband.
Using a safety pin, thread your elastic through the Back casing.
Before the end of the elastic is about to be pulled completely into the casing, sew up the waistband along the same line as the skirt’s side seam catching about a 1/2” of the elastic. Continue pulling the elastic through until it’s about 1/2 " past the other side seam. Close the openings with hand stitching.
Make button holes at the top front.
Hand stitch buttons at the straps.
2. Pants without frill strap
Turn right side out. and Press the top seam line.
Fold and press strap 1cm(3/8”) in horizontally to the wrong side.
Press seams open.
Match the front band and back band. Face the right sides. Stitch as shown, keeping opening unstitched.
Press seams open.
Now pleat the pants. Use pins to secure them then iron press them to keep the shape! Keep repeating this pleating process from the both sides to the center. For ease of work. Sew a sparsely spread out stitch along the top of the pleated cloth to hold the pleats together.
Pin and stitch the front and back side line together as shown. Right sides of fabric together. Serger or zig-zag stitch together.
Press seams toward the front.
Serge or zig-zag the top-edges of pocket.
Press 1.5cm(5/8)” and stitch the top edge of pocket first.
Iron the edges in toward the wrong side of the fabric on each pocket.
The pocket is now ready to topstitch onto your right side of pockets.
Align it based on the markings on your pattern.
Pin and stitch the front and back inseam line together as shown. Right sides of fabric together.
Pin the curves of two pants pieces together with right sides together and sew one big U that’s the curve. This is the curve that’s from the crotch to the top of the waist. Then Serger or zig-zag stitch together.
Sew the waistband-outside to the pants as shown. Face the right sides. And fold and press seam 1cm(3/8”) of waistband-inside in horizontally to the wrong side.
Fold the waistband down lengthwise along the pressed fold.Top stitch along the bottom of the waistband (about 1/8 inch from the seam between the waistband and the pants), making sure you're catching the inside of the waistband.
Fold twice concealing the cut edge and press. Sew the hem as shown.
Using a safety pin, thread your elastic through the Back casing.
Before the end of the elastic is about to be pulled completely into the casing, sew up the waistband along the same line as the pants side seam catching about a 1/2”of the elastic. Continue pulling the elastic through until it’s about 1/2 “ past the other side seam. Close the openings with hand stitching.
Make button holes at the top front.
Hand stitch buttons at the straps.
3. Romper with frill
Apply interfacing to the wrong side of snap button placket (2.5cm/1” wide).
Face the right sides of front romper pants and back romper pants together. Pin on and stitch along the side lines. Serge or zigzag red line at the edge as shown. Press seams towards back.
To gather the front romper pants simply hold the fabric still in one hand and pull one of the loose threads with the other.
Sew a parallel row of long(gathering) stitches around the skirt.
To gather the ruffle simply hold the fabric still in one hand and pull one of the loose threads with the other.
Do this on both sides until your each skirts are the same width as the each waist bands(front & back). Repeat with the other piece.
Serge or zigzag red line at the edge as shown. Press seams towards front.
On the wrong side of skirt, fold 0.5cm(3/16") concealing the cut edge and press. Sew the hem as shown.
Pin and baste stitch the romper skirt to the romper pants as shown.
Right side of romper skirt and wrong side of bodice together.
Sew the waistband-outside to the romper as shown. Face the right sides. And fold and press seam 1cm(3/8”) of waistband-inside in horizontally to the wrong side.
Fold the waistband down lengthwise along the pressed fold.
Top stitch along the bottom of the waistband (about 1/8 inch from the seam between the waistband and the skirt), making sure you're catching the inside of the waistband.
Do same as skirt and pants.
Serge or do zigzag the raw edge of leg line as shown.
On the wrong side of leg line, fold 1cm/3/4inch concealing the cut edge and press as shown.
And edge stitch along the leg line as shown.
Pull the elastic band trough the tunnel with the help of a safety pin.
Do a small stitch the elastic band to the beginning and end of leg line at both sides to fix as picture shown.
Serge or do zigzag the raw edge of snap button placket
On the wrong side of placket, fold 2cm/3/4 inch once concealing the cut edge and press.
Sew the croth line as shown. Repeat with the other side.
Make button holes at the top front.
Add snaps to the front and back placket.
Hand stitch buttons at the straps.
Romper without frill strap and without skirt
Turn right side out. and Press the top seam line.
Fold and press strap 1cm(3/8”) in horizontally to the wrong side.
Press seams open.
Match the front band and back band. Face the right sides. Stitch as shown, keeping opening unstitched.
Press seams open.
Apply interfacing to the wrong side of snap button placket (2.5cm/1” wide).
Face the right sides of front romper pants and back romper pants together. Pin on and stitch along the side lines. Serge or zigzag red line at the edge as shown. Press seams towards back.
To gather the front romper pants simply hold the fabric still in one hand and pull one of the loose threads with the other.
Sew the waistband-outside to the romper as shown. Face the right sides. And fold and press seam 1cm(3/8”) of waistband-inside in horizontally to the wrong side.
Fold the waistband down lengthwise along the pressed fold.
Top stitch along the bottom of the waistband (about 1/8 inch from the seam between the waistband and the skirt), making sure you're catching the inside of the waistband.
Do same as skirt and pants.
Serge or do zigzag the raw edge of leg line as shown.
On the wrong side of leg line, fold 1cm/3/4inch concealing the cut edge and press as shown.
And edge stitch along the leg line as shown.
Pull the elastic band trough the tunnel with the help of a safety pin.
Do a small stitch the elastic band to the beginning and end of leg line at both sides to fix as picture shown.
Serge or do zigzag the raw edge of snap button placket
On the wrong side of placket, fold 2cm/3/4 inch once concealing the cut edge and press.
Sew the croth line as shown. Repeat with the other side.
Make button holes at the top front.
Add snaps to the front and back placket.
Hand stitch buttons at the straps.
댓글
댓글 쓰기