Cut bias binding.
Flat piping-Fold bias binding in half width wise.
Piping with cord- Lay the cotton cording in the center of the bias tape, then gently fold the long ends of the bias so
that the fabric is wrong sides together, making sure to match up both long edges.
Set up your machine with your zipper foot. I have moved my needle to the far left position.
You will use long stitches as you are essentially just basting the fabric into place.
Then sew it.
You can choose flat piping or piping with cord as you wish or without piping as you wish.
Sew the piping along the outline of collar using a 0.6cm(1/4″) seam allowance.
Face the right sides of collars together. Pin on and stitch along the seam lines as shown.
Turn it right side out through opening.Then Iron them.
Give the top stitching along the edge line of collar(optional).
Sew the piping along the top line of pocket using a 0.6cm(1/4″) seam allowance.
Sew the piping along the top line of bottom pocket using a 0.6cm(1/4″) seam allowance as shown.
Put bottom pocket over the top pocket and give the top stitching over the matching pockets.
Face the right sides of outer pocket and lining pocket pocket together.
Pin on and stitch along the seam lines as shown.
Turn it right side out through opening.Then Iron them.
Face the right sides of back ties together.
Pin on and stitch along the side lines as shown.
Turn it right side out through opening.
Then Iron them.
Serge the vertical line of frill. Face the right sides of front and back of frill together.
Serge the edge line of frill. Fold 0.2”(0.5cm) concealing the cut edge and press. Sew the hem as shown.
Sew a parallel row of long(gathering) stitches around the frill.(Stitch length long, tension low/loose) Gathering the frill.
Pin and sew the shoulders together with
right sides of fabric together. Iron seams open.
Repeat with lining fabric.
Pin the piping on the right side of your fabric. You can pin the piping into place before you get started.
On the right side of your fabric, machine baste the piping facing inwards matching the raw edges as picture shown.
16-2. Pin the collar and baste stitch-0.6cm(1/4”) along the neckline.
Stitch-0.6cm(1/4”) the Shoulder frills to the bodice with right sides together as shown.
Serge or zigzag stitch the seams together as shown.
You should have 2 seperate fronts and backs now(one is outer fabric, the other one is lining fabric).
Now with the right sides of the fronts and backs facing each other, sew along the neck line and front center and arm
side line as shown.Trim the points on any sharp angles. Through the back hem line, turn the piece right-side-out.
Using your CB (center back line) as a guide, lay your left piece overlapping the right piece and pin in place.
Sew the baste stitch.
Then match the front waist band(outer fabric) to the front waist band(lining fabric), with right sides together as shown.
Fold side waist band in half width wise.
Sew the baste stitch back tie to the outer fabric of
front waist band as shown.
Match the front band and side band. Face the right sides. And match the back band and side band again.
Face the right sides.
Stitch them as shown. Press seams open.
Fold 1cm(3/8") inside & press at the bottom
of lining waist band as picture shown.
Pleat the bottom part. Use pins to secure them then iron press them to keep the shape.
Keep repeating this pleating process from the left to the right sides.
For ease of work, sew a sparsely spread out stitch along the top of the pleated cloth to hold the pleats together.
The pocket is now ready to topstitch onto your right side of pockets.
Align it based on the markings on your pattern. Edge stitch the pockets as shown.
Face the right sides of skirt together. Pin on and stitch along the side lines.
Serge or zigzag red line at the edge as shown. Press seams towards back
Sew the waistband-outside to the skirt as shown.
Iron waistband seam upward.
Stitch the elastic band on the both side line of side waist band(outer part) to fix as shown.
Fold the waistband down lengthwise along the pressed fold.
Streach out the elastic band and place it.
inside of the waist band.Stitch fixed as shown.
Then top stitch along the bottom of the waistband (about 1/8 inch from the seam between the waistband
and the skirt), making sure you're catching the inside of the waistband.
On the wrong side of skirt, fold twice concealing the cut edge and press. Sew the hem of skirt as shown.
댓글
댓글 쓰기