#1. Long suspender pants
Apply interfacing to the wrong side of front piece.
Fold suspender loop diagonally.
And stitch as shown. 
Trim the rest.
Turn it inside out.
Then sew a basting stitch loop as shown for fixing as shown.
Now with the right sides of the front-outer fabric and front lining each other, sew along the top edge as shown.
Trim the points on any sharp angles and cut notches in the seam allowance along the curve.
Turn the piece right-side-out. Press the edges.
With the right sides of front and back, matching up the side seams.
Pin together front and back side seams, with the right sides together. You will need to lift up the front piece. Sew. Repeat for both sides. Press seams open.
Stitch as shown, keeping opening unstitched.
Now pleat the pants. Use pins to secure them then iron press them to keep the shape.
Keep repeating this pleating process from the center to the both sides.
For ease of work, sew a sparsely spread out stitch along the top of the pleated cloth to hold the pleats together.
Face the right sides of front pants and back pants together. Pin on and stitch along the side lines. Serge or zigzag red line at the edge as shown. Press seams towards back.
Once you sew the inner leg portion of the pants, flip one of the legs right side out. Tuck the pant leg that’s right side out inside the wrong side out pant leg with the crotch part lined up. The two pant legs should have the right sides touching.
Pin the curves together and sew one big U that’s the curve. This is the curve that’s from the crotch to the top of the waist.cThen if you have a serger, you can serge or zig zag the seam allowance as shown.
Match the bodice to pants waist line with right sides together as picture shown.
Align the pants and bodice right sides together.
Pin all the way around waist line
and sew as shown. Serge or do zigzag the raw edge.
Fold twice concealing the cut edge and press. Sew the hem as shown.
For back suspender loop, Press fold line.
Fold the entire strap, Topstitch the edges.
Fold the strap in half lengthwise.
Stitch back suspender loop on the center of back band as shown.
Insert elastic band into the side seam opening.
Before the end of the elastic is about to be pulled completely into the casing, sew up the waistband along the same line as the pants’s side seam catching about a 1/2”of the elastic. Continue pulling the elastic through until it’s about 1/2 “ past the other side seam.
Close the openings with hand stitching.
To press the strap, fold it in half, press. Then open it and fold the edges to the center, press.
And fold approximately 3/8”(1cm) both side of strap in widthwise.
Then fold the strap in half one more time and press.
Next you'll topstitch along long edge and short edge of the strap as shown.
Pass the strap through the loop and give a little stitch on the middle of strap for fixing as shown.
#2. Short suspender pants
Apply interfacing to the wrong side of front piece.
Now with the right sides of the front-outer fabric and front lining each other, sew along the top edge as shown.
Trim the points on any sharp angles and cut notches in the seam allowance along the curve.
Turn the piece right-side-out. Press the edges.
With the right sides of front and back, matching up the side seams.
Pin together front and back side seams, with the right sides together.
You will need to lift up the front piece. Sew. Repeat for both sides. Press seams open.
Stitch as shown, keeping opening unstitched.
Now pleat the pants. Use pins to secure them then iron press them to keep the shape.
Keep repeating this pleating process from the center to the both sides.
For ease of work, sew a sparsely spread out stitch along the top of the pleated cloth to hold the pleats together.
Face the right sides of front pants and back pants together. Pin on and stitch along the side lines. Serge or zigzag red line at the edge as shown. Press seams towards back.
Once you sew the inner leg portion of the pants, flip one of the legs right side out. Tuck the pant leg that’s right side out inside the wrong side out pant leg with the crotch part lined up. The two pant legs should have the right sides touching.
Pin the curves together and sew one big U that’s the curve. This is the curve that’s from the crotch to the top of the waist.cThen if you have a serger, you can serge or zig zag the seam allowance as shown.
Fold twice concealing the cut edge and press. Sew the hem as shown.
Match the bodice to pants waist line with right sides together as picture shown.
Align the pants and bodice right sides together.
Pin all the way around waist line
and sew as shown. Serge or do zigzag the raw edge.
Fold 1cm(3/8”) four edges and press. Then fold in half widthwise as shown.
Next you'll topstitch along long edge and short edge of the strap as shown.
Pin and stitch the straps in place on the back waist band.
Insert elastic band into the side seam opening.
Before the end of the elastic is about to be pulled completely into the casing, sew up the waistband along the same line as the pants’s side seam catching about a 1/2”of the elastic. Continue pulling the elastic through until it’s about 1/2 “ past the other side seam.
Close the openings with hand stitching.
For strap loop, Press fold line.
Topstitch the edges.
Fold the strap in half lengthwise.
Then stitch it and turn it inside out.
Press seams open.
Pass the strap through the loop as shown.
#3. Pumpkin suspender pants
Fold 1cm(3/8”) three edges(except front edge) and press. Then fold in half widthwise as shown.
Next you'll topstitch along long edge and short edge of the strap as shown.
With right sides together pin straps into place on front.
Now with the right sides of the front outer fabric and lining each other.
Sew along the top edge as shown.
Press seam s open.
With the right sides of front and back, matching up the side seams.
Pin together front and back side seams, with the right sides together.
You will need to lift up the front piece. Sew. Repeat for both sides. Press seams open.
Stitch as shown, keeping opening unstitched.
Apply interfacing to the wrong side of middle strap piece.
Fold 1cm(3/8”) four edges and press.
Then fold in half widthwise as shown.
Next you'll topstitch along long edge and short edge of the strap as shown.
Make button holes as shown.
Now pleat the pants. Use pins to secure them then iron press them to keep the shape.
Keep repeating this pleating process from the center to the both sides.
For ease of work, sew a sparsely spread out stitch along the top of the pleated cloth to hold the pleats together.
Face the right sides of front and back together.
Pin on and stitch along the side line only.
Sereg or zigzag seams at the edge as picture shown.
Repeat with the another piece.
Face the right sides of two pieces together.
Pin on and stitch along the front center line and back center line as shown.
Sereg or zigzag seams at the edge as picture shown.
Fold the 1cm(3/8”) from the raw edge to the wrong side and then 1.5cm(9/16”) again.
Then edge stitch it as shown. Repeat with the other piece.
Pull the elastic band trough the hem tunnel with the help of a safety pin.
Do a small stitch the elastic band to the beginning and end of leg line at both sides to secure
as shown.
Match the bodice to pants waist line with right sides together as picture shown.
Align the pants and bodice right sides together.
Pin all the way around waist line
and sew as shown. Serge or do zigzag the raw edge.
Insert elastic band into the side seam opening.
Before the end of the elastic is about to be pulled completely into the casing, sew up the waistband along the same line as the pants’s side seam catching about a 1/2”of the elastic. Continue pulling the elastic through until it’s about 1/2 “ past the other side seam.
Close the openings with hand stitching.
Apply interfacing to the wrong side of snap crotch as shown.
Fold in half line with the right side.
Then fold 1cm(0.4”) in horizontally to the wrong side.
And sew down the short each side as shown. 
Trim the points on any sharp angles.
Turn it right side out.
Working from the wrong side of the garment, pin and sew snap crotch to garment aligning the raw edges of crotch line as shown.
Fold the raw edge of the snap crotch under along the line you pressed earlier, and pin this fold to the inside of the front. Topstitch the snap crotch to the front close to the inside fold. Repeat on the other side.
Make button holes as shown.
#4. Suspender dress
Fold 1cm(3/8”) three edges(except front edge) and press. Then fold in half widthwise as shown.
Next you'll topstitch along long edge and short edge of the strap as shown.
Apply interfacing to the wrong side of front piece.
With right sides together pin straps into place on front.
Now with the right sides of the front-outer fabric and front lining each other, sew along the top edge as shown.
Trim the points on any sharp angles and cut notches in the seam allowance along the curve.
Turn the piece right-side-out. Press the edges.
With the right sides of front and back, matching up the side seams.
Pin together front and back side seams, with the right sides together.
You will need to lift up the front piece. Sew. Repeat for both sides. Press seams open.
Stitch as shown, keeping opening unstitched.
Sew a parallel row of long(gathering) stitches around the skirt.
(Stitch length long, tension low/loose)
Gathering the top edge of skirt.
To gather the front skirt fabric simply hold the fabric still in one hand and pull one of the loose threads with the other.
Do this on both sides until your front skirt is the same width as the each waist.
Repeat with the back piece. 
Match the bodice to pants waist line with right sides together as picture shown.
Align the pants and bodice right sides together.
Pin all the way around waist line
and sew as shown. Serge or do zigzag the raw edge.
Insert elastic band into the side seam opening.
Before the end of the elastic is about to be pulled completely into the casing, sew up the waistband along the same line as the pants’s side seam catching about a 1/2”of the elastic. Continue pulling the elastic through until it’s about 1/2 “ past the other side seam.
Close the openings with hand stitching.
Make button holes as shown.
Fold twice concealing the cut edge and press. Sew the hem as shown.
댓글
댓글 쓰기